GIGABYTE GA-X48-DS5 SATA2 DRIVERS

GIGABYTE GA-X48-DS5 SATA2 DRIVER DETAILS:

Type: Driver
File Name: gigabyte_ga_17916.zip
File Size: 12.8 MB
Rating:
4.92
80 (4.92)
Downloads: 58
Supported systems: Windows 10, 8.1, 8, 7, 2008, Vista, 2003, XP, Other
Price: Free* (*Free Registration Required)

Download Now
GIGABYTE GA-X48-DS5 SATA2 DRIVER



Sometimes there is an incompatibility with a psu and mobo, even though your psu might work fine with another setup. You might need to remove your cpu and inspect the mobo cpu socket for possible bent pins. Make sure that the socket and the bottom of your cpu are clean and that Gigabyte GA-X48-DS5 SATA2 aren't any particles or other debris on both surfaces.

Immediately re-enter the bios and then make any needed bios changes. Make sure that the motherboard supports the memory.

It is recommended that memory of the same capacity, brand, speed, and chips be used. Always turn off the computer and unplug the power cord from the power outlet before installing the memory to Gigabyte GA-X48-DS5 SATA2 hardware damage.

GIGABYTE X48-DS5

Memory modules have a foolproof design. A memory module can be installed in only one direction. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth. The four DDR2 memory sockets are divided into two channels and each channel has two Gigabyte GA-X48-DS5 SATA2 sockets as following: Dual Channel mode cannot be enabled if only one DDR2 memory module is installed.

ShieldSquare reCAPTCHA Page

When enabling Dual Channel Gigabyte GA-X48-DS5 SATA2 with two or four memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used and installed in the same colored DDR2 sockets for optimum performance. When memory modules of different capacity and chips are installed, a message which says memory is operating in Flex Memory Mode will appear during the POST.

GA-XDS5 Motherboard 17 Installing a Memory Before installing a Gigabyte GA-X48-DS5 SATA2 module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. Follow the steps below to correctly install your memory modules in the memory sockets. Note the orientation of the memory module. Spread the retaining clips at both ends of the memory socket. Place the memory module on the socket.

As indicated in the picture on the left, place your fingers on the top edge of Gigabyte GA-X48-DS5 SATA2 memory, push down on the memory and insert it vertically into the Gigabyte GA-X48-DS5 SATA2 socket. The clips at both ends of the socket will snap into place when the memory module is securely inserted Hardware Installation 18 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card: Make sure the motherboard supports the expansion card.

GIGABYTE GA-X48-DS5 SATA2 WINDOWS 10 DOWNLOAD DRIVER

Carefully read the manual that came Gigabyte GA-X48-DS5 SATA2 your expansion card. Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.

Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel. Align the card with the slot, and press Gigabyte GA-X48-DS5 SATA2 on the card until it is fully seated in the slot. Make sure the metal contacts on the card are completely inserted into the slot.

Gigabyte GA-XDS5 Manual

Secure the card's metal bracket to the chassis back panel with a screw. After installing all expansion Gigabyte GA-X48-DS5 SATA2, replace the chassis cover s. Free Download Gigabyte GA-XDS5 (rev. 1.x) SATA2 Preinstall Driver x86 (Other Drivers & Tools). Revolution energy saving design with DES Advanced technologySupports Intel® Core 2™ multi-core and 45nm processors MHz FSB (Front Side Bus)  Missing: SATA2.

Related Drivers