HP ENVY 23-D110EE TOUCHSMART REALTEK CARD READER WINDOWS 10 DRIVER

HP ENVY 23-D110EE TOUCHSMART REALTEK CARD READER DRIVER DETAILS:

Type: Driver
File Name: hp_envy_34557.zip
File Size: 4.1 MB
Rating:
4.38
55 (4.38)
Downloads: 37
Supported systems: Windows 10, 8.1, 8, 7, 2008, Vista, 2003, XP, Other
Price: Free* (*Free Registration Required)

Download Now
HP ENVY 23-D110EE TOUCHSMART REALTEK CARD READER DRIVER



Before you begin Have a Phillips head screwdriver ready. Turn off the computer, disconnect the Ethernet or modem cable, and disconnect the power cord. Transfer the computer to a clean, flat, stable work surface over a noncarpeted floor. HP recommends that you put down a blanket, towel, or other soft cloth to protect the screen from scratches or other damage. Use an antistatic wrist strap and a conductive foam pad when working on the computer. Electrostatic discharge ESD can damage your processor, disk drives, expansion boards and other components. HP strongly recommends the use of the wrist strap and conductive foam pads to reduce the risk of damage to your computer. Remove a component from its protective packaging only when you are ready HP ENVY 23-d110ee TouchSmart Realtek Card Reader install it.

This product contains components that can be damaged by electrostatic discharge ESD. To reduce the chance of ESD damage, work over a noncarpeted floor, use a static dissipative work surface such as a conductive foam padand wear an ESD wrist strap connected to a grounded surface.

HP ENVY 23-D110EE TOUCHSMART REALTEK CARD READER TREIBER WINDOWS 7

Video overview View the following video before using the steps in this article. Removing the MXM graphics card Use the following steps to remove the graphics card: Step 2 Pull out the USB dongle if it is present in your computer. The EMI shield screw locations are marked with a stencil of an arrow that does not have a circle inside.

Royal-ProductDetail

Step 4 Carefully tip the shield up and pull it off the computer. Step 5 Next, loosen the four screws securing the thermal module to the CPU. Step 6 Detach the HP ENVY 23-d110ee TouchSmart Realtek Card Reader near the radiator end of the thermal module. Step 7 Carefully lift the CPU thermal module out of the computer. Step 9 Detach the screw near the radiator end of the MXM thermal module. Step 10 Carefully lift the MXM thermal module out of the computer. Step 11 Detach the two small screws on the graphics card Step 1 To replace the graphics card, align the card into its slot at a 45 degree angle.

Step 2 Push the card down into the slot and replace the two screws. Hold the card down while replacing the first of the two screws.

HP ENVY 23-D110EE TOUCHSMART REALTEK CARD READER DRIVER WINDOWS

Step 3 Before replacing the MXM thermal module assembly, first clean the old thermal solution from the MXM graphics card by applying a cleaning agent and then wiping it clean. Step 4 Repeat the cleaning procedure on the thermal module. Step 5 Apply new thermal grease or thermal pad to the MXM graphics card.

Advanced Card ACR88 USB BUS DriverProduct release information
AIMS Lab Xtreme98 WDM Video CapturePopular Forums

Step 6 Carefully align the MXM thermal module back onto the computer. Step 7 Tighten the screws over the MXM graphics card.

HP ENVY 23-D110EE TOUCHSMART REALTEK CARD READER DRIVER FOR WINDOWS DOWNLOAD

Step 8 Replace the screw near the radiator. Step 9 Before replacing the CPU thermal module assembly, first clean the thermal solution from the CPU by applying a cleaning agent and then wiping it clean. Step 10 Repeat the cleaning procedure on the thermal module. Step 11 Apply new thermal grease or thermal pad to the CPU. Step 12 Carefully align the thermal module back onto the computer, sliding the radiator between the MXM thermal module and the system fan.

HP ENVY 23-d118d TouchSmart Realtek Card Reader Driver for Windows 8

Step 13 Tighten the screws for the CPU thermal module. Step 14 Replace the screw near the radiator. Step 15 To replace the motherboard EMI shield, find the small slot on the side of the shield Step 16 Find the two small holes on the bottom of the EMI shield Step 17 To replace the HP ENVY 23-d110ee TouchSmart Realtek Card Reader EMI shield, align the slot on the shield over its alignment tab, and carefully swing and press the shield into place.

Step 18 Make sure the bottom holes on the shield are resting flat around the alignment tabs. Step 19 Replace the five screws for the motherboard shield. Each screw location is marked with a stencil of an arrow without a circle inside. Step 20 Step 21 Replace the rear cover. Free Download HP ENVY dee TouchSmart Realtek Card Reader Driver for Windows 8 (Card Readers).

HP ENVY dee TouchSmart Realtek Card Reader Driver for Windows 8. 9 downloads. Card Readers Realtek. Windows 8 64 bit.

Related Drivers